Question for upgrading

[Egoitz Aurrekoetxea]

Hi mate, 

I think (and say think :) )I finally found a method. Although I'm
testing it deeply... it seems (say seems too :) ) 2.4 is compatible with
a mail spool in 2.3 (at least with my config). So I'll try to upgrade
first to 2.4 and later to 3.0 setting up a replication from 2.4 to 3.0.
Would be fine if Bron, Ellie or someone at Fastmail could tell something
about it to us :) :) 

Cheers!

---

EGOITZ AURREKOETXEA 
Departamento de sistemas 
944 209 470
Parque Tecnológico. Edificio 103
48170 Zamudio (Bizkaia) 
egoitz at sarenet.es 
www.sarenet.es [1] 
Antes de imprimir este correo electrónico piense si es necesario
hacerlo. 

El 16-12-2018 22:24, John Capo escribió:

> On Thu, December 13, 2018 13:25, Egoitz Aurrekoetxea wrote: 
> 
>> Hi again!
>> 
>> Else as a simplication way can you replicate any manner a 2.3 with some
>> newer version?. At least in manual mode (not rolling)?.
> 
> The replication protocol in 2.4 is not compatible wit 2.3.
> 
> There is no easy way.  I'm rsync'ing one account at a time between 2.3 and 2.4 with IMAP/POP and LMTP access disabled, followed by a reconstruct, and then enabling IMAP/POP and LMTP access.
> 
> Many terrabytes to go.
> 
> You could also look at imapsync but its slow.
> 
> Cheers.
> 
> ---
> 
> EGOITZ AURREKOETXEA
> Departamento de sistemas
> 944 209 470
> Parque Tecnológico. Edificio 103
> 48170 Zamudio (Bizkaia)
> egoitz at sarenet.es www.sarenet.es [1] [1 [1]] Antes de imprimir este correo electrónico piense si es
> necesario hacerlo.
> 
> El 13-12-2018 16:52, Egoitz Aurrekoetxea escribió:
> 
> Good afternoon,
> 
> I was trying to upgrade part of our Cyrus imap installation, concretely that one consisting in
> still 2.3. I was planning to set up Cyrus 3.0. I have seen all works properly except for the
> unexpunge command because as someone stated here, a reconstruct -V max was needed.The problem
> is that this reconstruct command, takes ages and I'm not able to keep the service offline so
> many time. So I have been thinking in the following scenario :
> 
> - Cyrus 2.3 master -> Cyrus 2.4 slave
> 
> Get this 2.4 slave ready and set it as master. But here comes my first doubt. Does the 2.4
> replication work with the 2.3 replication?. Can in this pair, both (the 2.3 and the 2.4) be
> both master and slave?. I mean to switch roles in the pair. Make one become master and the
> other slave and  vice versa?.
> 
> Let's think now Cyrus 2.4 is ready and working.
> 
> - Now, I would set up a new 3.0 slave. I know 2.4 could replicate with 3.0. So I would get the
> 3.0 ready and then set 3.0 as master. Can in this pair both the 2.4 and 3.0 be master and
> slave?. Meaning again to the same role switching commented before... to make one to be master
> and the other slave or vice versa....
> 
> I'l will end up with 2 3.0 master and slave... but I need to trace the path...
> 
> Does anyone see any other way?.
> 
> Best regards,
> 
> -
> 
> --
> 
> EGOITZ AURREKOETXEA
> Departamento de sistemas
> 944 209 470
> Parque Tecnológico. Edificio 103
> 48170 Zamudio (Bizkaia)
> egoitz at sarenet.es www.sarenet.es [1] [1 [1]] Antes de imprimir este correo electrónico piense si es
> necesario hacerlo. ----
> Cyrus Home Page: http://www.cyrusimap.org/
> List Archives/Info: http://lists.andrew.cmu.edu/pipermail/info-cyrus/
> To Unsubscribe:
> https://lists.andrew.cmu.edu/mailman/listinfo/info-cyrus
> 
> Links:
> ------
> [1] http://www.sarenet.es

 

Links:
------
[1] http://www.sarenet.es
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.andrew.cmu.edu/pipermail/cyrus-devel/attachments/20181217/fd85fb49/attachment.html>